New Boot solutions for Delphi on heavy-duty vehicles and automobiles

Flex version 6.31.0.0 out now

New Flex update to program in Boot mode Delphi ECUs installed on JCB, Landini Tractors, McCormick heavy vehicles and on Kia, Hyundai, Mahindra, Volkswagen, Seat, Skoda, Great Wall automobiles.

Four new ECUs are supported as of today:

• Delphi DCM2.7AP
• Delphi DCM3.7 VAG
• Delphi DCM7.1AP
• Delphi DCM7.24

Thanks to these protocols, it is possible to read and write the whole content of Flash and EEPROM memories and to restore the Delphi DCM3.7 VAG ECU in case of wrong OBD writing. Restoring will be possible by contacting the tech support.

Some of the supported vehicles:

• Hyundai i20 1.5L CRDi 100PS
• Great Wall Poer 2.0L Wingle 7 140PS
• Kia Seltos 1.5L CRDi 115PS
• JCB Wheel Loaders 2.5L 75PS
• JCB Telehandler 4.4L 75PS
• Landini Tractors Rex3 2.5L 55PS
• Mahindra Xuv 1.5L 115PS
• Seat Ibiza 1.2L TDI 75PS
• Skoda Fabia 1.2L TDI 75PS
• VW Polo 1.2 TDI 75Ps

This new protocol is available for the following software packages:
DCM2.7AP – Boot

• FLS0.4M – SW Flex Boot Nexus MPC5xxx Master
• FLS0.4S – SW Flex Boot Nexus MPC5xxx Slave
• FLS0.5M – SW Flex Full Master
• FLS0.5S – SW Flex Full Slave

DCM3.7 VAG – Boot

• FLS0.5M – SW Flex Full Master
• FLS0.5S – SW Flex Full Slave
• FLS0.6M – SW Flex OBD/Bench/Boot Renesas SH7xxxx Master
• FLS0.6S – SW Flex OBD/Bench/Boot Renesas SH7xxxx Slave

DCM7.1AP – Boot

• FLS0.5M – SW Flex Full Master
• FLS0.5S – SW Flex Full Slave
• FLS0.10M – SW Flex Bench/Boot Infineon TC17xx / TC2xx / TC3xx Master
• FLS0.10S – SW Flex Bench/Boot Infineon TC17xx / TC2xx / TC3xx Slave

DCM7.24 – Boot

• FLS0.5M – SW Flex Full Master
• FLS0.5S – SW Flex Full Slave
• FLS0.10M – SW Flex Bench/Boot Infineon TC17xx / TC2xx / TC3xx Master
• FLS0.10S – SW Flex Bench/Boot Infineon TC17xx / TC2xx / TC3xx Slave

Newly added protocols:
(Boot)

• Mahindra Delphi DCM2.7AP MPC5642 Read/Write/Checksum Calculation Internal Flash

Reading Time: ~ 1.40 minutes  Writing Time: ~ 1.20 minutes

• JCB Delphi DCM2.7AP MPC5643 / MPC5644 Read/Write/Checksum Calculation Internal Flash

Reading Time:~ 1.40 minutes  Writing Time:~ 1.20 minutes

• VAG Delphi DCM3.7 SH72513 Read Full Backup, Write Recovery

Reading Time: ~ 15 seconds Writing Time: ~ 5 seconds 

• All Delphi DCM7.1AP  TC277 Read/Write/Checksum Calculation Internal Flash, Read/Write/Checksum Calculation Internal EEPROM, Full Backup

Reading Time:~ 1.20 minutes  Writing Time: ~ 20 seconds

• JCB Delphi DCM7.24  TC277 Read/Write/Checksum Calculation Internal Flash, Read/Write/Checksum Calculation Internal EEPROM, Full Backup

Reading Time: ~ 1.20 minutes  Writing Time: ~ 20 seconds

• JCB Delphi DCM7.24  TC297 Read/Write/Checksum Calculation Internal Flash, Read/Write/Checksum Calculation Internal EEPROM, Full Backup

Reading Time: ~ 1.20 minutes  Writing Time: ~ 20 seconds

Bug fixes:

• Added new CRC type for VAG Bosch MG1CS011
• Added new CRC type for VAG Continental Simos8.2
• Added new CRC type for Mercedes Continental MCM / ACM
• Added new CRC type for Land Rover Denso
• Added new CRC type for Ford Delphi MPC555
• Porsche Continental SDIx OBD – fixed issue which needed throttle reset
• BMW Exx Series OBD – fixed writing which cause OBD bricking for some SW versions

Software improvements:

• Improved Autodetection System in MCM / ACM protocols

Click here to discover the full list of supported vehicles.